What does mg/g mean on cannabis?

mg/g means milligrams of the named substance per gram of the material tested. To convert mg/g to a mass percentage, divide by 10: 125 mg/g equals 12.5%. To convert back, multiply the percentage by 10. This changes the units, not the substance or the meaning of the result.

A cannabis certificate of analysis, or COA, may contain several kinds of measurement. Cannabinoid concentration, the amount in a package, and a contaminant result answer different questions. Start with the compound name and the unit beside its result; a number without those labels is incomplete.

Sources: Converting Potency from mg/g to % (undated; accessed October 2026) (2026); Understanding Your Hemp and Cannabis COAs (2020)

Cannabis COA units at a glance

The denominator—the part after the slash—tells you what the amount is relative to. A gram is a unit of mass; a milliliter is a unit of volume. Neither is automatically a serving or a package. A liquid can be reported in mg/g as well as mg/mL.

COA units. Scroll to compare.
Unit on reportWhat it describesCheck before comparing
mg/gMilligrams per gram of materialSame compound and reporting basis
% or wt%Often a mass percentage on a potency reportConfirm that the percentage refers to mass
mg/mLMilligrams per milliliter of liquidDensity is needed to compare with mg/g
mg/unit or mg/servingAmount in the defined unit or servingHow the report defines that unit or serving
mg/packageAmount attributed to the whole packagePackage identity and size
µg/g or mg/kgEquivalent mass-based trace concentrationsBoth equal mass-based ppm; confirm the basis

Sources: NIST Guide to the SI, Chapter 8: Comments on Some Quantities and Their Units (2008); How to read and understand a cannabis product label (2026); Understanding Your Hemp and Cannabis COAs (2020)

How to convert mg/g to percent THC or CBD

There are 1,000 milligrams in a gram. A hypothetical result of 125 mg/g therefore means 125 milligrams out of 1,000 milligrams of material: 125 ÷ 1,000 × 100 = 12.5%. The shortcut is mg/g ÷ 10. The same arithmetic applies to CBD or another named compound when both values describe the same mass fraction.

Worked examples: 7.5 mg/g = 0.75%; 42 mg/g = 4.2%; 125 mg/g = 12.5%. In reverse, 0.75% × 10 = 7.5 mg/g. These are invented arithmetic examples, not product results or recommended amounts.

Keep the result label intact. Converting a delta-9 THC concentration does not turn it into total THC, and converting THCA does not turn it into THC. Those are questions about chemical identity and the laboratory’s calculation, not unit conversion. Likewise, an ND result cannot be converted into a measured zero.

Sources: Converting Potency from mg/g to % (undated; accessed October 2026) (2026); Understanding Your Hemp and Cannabis COAs (2020)

mg/g vs mg/mL CBD: why density matters

mg/g describes an amount relative to mass. mg/mL describes an amount relative to volume. To connect them, you need the density of the actual liquid—the mass of one milliliter under the relevant conditions. Do not assume every cannabis oil has the same density, or that a gram of oil occupies exactly one milliliter.

The relationship is: mg/mL = mg/g × density in g/mL. In reverse: mg/g = mg/mL ÷ density in g/mL. The grams cancel in the first calculation, leaving milligrams per milliliter.

For an invented liquid containing 20 mg/g of CBD with a stated density of 0.90 g/mL, the equivalent concentration is 18 mg/mL: 20 × 0.90 = 18. Checking backward gives 18 ÷ 0.90 = 20 mg/g. This is a dimensional calculation, not a dosing instruction or a claim about a particular oil.

If density is absent, a precise conversion between these two units is not supported by the report. Request the relevant product density from the laboratory or manufacturer. A general oil-density estimate should not be presented as a measured value for an unidentified product.

Sources: NIST Guide to the SI, Chapter 8: Comments on Some Quantities and Their Units (2008); Converting Potency from mg/g to % (undated; accessed October 2026) (2026)

Per unit, per serving, and per package are different

Health Canada’s label guide distinguishes amount by weight, amount by unit, and total package amount. A COA may also state mg per serving or mg per package. Read the definition: unit might refer to one discrete item, while a package can contain several items. Serving and unit need not mean the same thing.

Imagine a teaching label reporting 2 mg of a named compound per unit and four identical units per package. Its arithmetic package total is 8 mg. Calling the per-unit value the package total would omit three units. This example illustrates label accounting only; it does not say what anyone should consume.

Concentration requires another quantity to give an amount. A mass-based concentration is multiplied by the corresponding material mass; a volume-based concentration is multiplied by the corresponding volume. Use net product contents, not packaging weight, and verify that the concentration and contents refer to the same product and basis.

A dropper is a device, not a universal volume unit. Unless the device or documentation establishes the volume, “one dropper” cannot supply the missing milliliters in a calculation. Neither a package total nor a concentration states how much a person absorbs.

Sources: How to read and understand a cannabis product label (2026); NIST Guide to the SI, Chapter 8: Comments on Some Quantities and Their Units (2008)

What do ppm, µg/g, and mg/kg mean?

When ppm describes a mass fraction, 1 ppm = 1 mg/kg = 1 µg/g. The µ symbol means micro: one microgram is one thousandth of a milligram. By contrast, 1 mg/g = 1,000 mg/kg, so confusing mg/g with µg/g introduces a thousand-fold error.

An illustrative contaminant result of 0.4 µg/g is therefore 0.4 mg/kg, or 0.4 ppm on a mass basis. It is not 0.4 mg/g. This conversion alone says nothing about whether the result meets an applicable requirement.

Parts per million does not identify the underlying quantity by itself. Confirm whether the laboratory means a mass fraction or another basis. Do not automatically treat ppm as mg/L for an oil: converting a mass fraction to mass per volume requires density. Explicit units and the report’s legend are more informative than the abbreviation alone.

Sources: The International System of Units (SI), Section 5: Writing unit symbols and names, and expressing values of quantities (2019); NIST Guide to the SI, Chapter 8: Comments on Some Quantities and Their Units (2008); Understanding Your Hemp and Cannabis COAs (2020)

Read the illustrated example without changing its meaning

The illustration is an original teaching diagram with invented numbers, not a certificate for a real product. Its first comparison shows the same mass fraction written two ways: 125 mg/g and 12.5%. Its second comparison shows why a density value is needed to connect 20 mg/g with 18 mg/mL.

Before comparing a label and COA, match the batch, named compound, units, and reporting basis. A dry-weight result uses a different denominator from an as-received result; merely dividing by 10 does not reconcile different moisture bases. Ask the laboratory when that basis is unclear.

Unit conversion also cannot resolve different samples, testing methods, or uncertainty. Preserve qualifiers such as ND or less than LOQ rather than replacing them with exact numbers. If the quantity, basis, or qualifier is missing, the useful next step is clarification—not extra decimal places.

Sources: Understanding Your Hemp and Cannabis COAs (2020); Cannabis Laboratory Quality System Standard (2026)